Vesconite Hilube keeps golf courses lush and green
30 September 2022

Keeping a golf course lush and emerald green is an important consideration for any golf course maintenance or irrigation engineer.

As a result, when a well-known original equipment manufacturer’s pumps’ wear parts were consistently failing, and resulting in less than optimum greens and fairways, a South African golf-course irrigation company turned to Vesconite Bearings to test prototype bushings and wear rings.

The global golf course context

Globally, the golf industry is large, with the US industry (which represents half of global golf courses) estimated to have an impact of USD70b on the US economy, according to Golf Course Industry’s 2017 Golf Industry Outlook.

Maintenance spending in the US totals $9b each year, according to the same survey, with around 56% allocated to labour and the remainder to other expenses, including irrigation costs, which are believed to make up one of the largest parts of these maintenance costs, with the importance of watering, overwatering, the existence of brown patches in the grass, grass thinning or loss of colour consuming much attention. Various other countries, including Canada, are said to have 2/3 of the maintenance budget of the average US course for each of their courses, but, whatever the global golf-course maintenance budget, the sums that are being spent on golf-course maintenance and on irrigation are substantial.

Interestingly, the US, Japan, Canada, England, Australia, Germany, France, Scotland, South Africa, etc., have the largest number of golf courses in that order, with irrigation playing a more or less important role depending on how scarce water is and whether the golf courses are open year round, among other factors.

Since many golf courses are located in water-scarce areas, irrigation can be challenging, especially since golf-course irrigation needs are often pitted against communities’ basic water needs. Capturing storm water, using water from dams and rivers, and re-using effluent and wastewater are all possible alternatives. These are all possible substitutes to using potable water … but they sometimes bring their own challenges that original equipment manufacturers may not be considering sufficiently.

The case study

The irrigation company that eventually switched to Vesconite Hilube bowl bushings and wear rings is a well-established provider of irrigation solutions to the many of South Africa‚Äôs 532 golf courses, of which 400 are under irrigation. Each South African golf course typically has three to 16 pumps, although the number of pumps can be as high as 38, as on one elite South African golf course designed by Jack Nicklaus.  Each pump typically has four to 12 stages in its multiple-stage canister pumps, which are the type specified by a large golf-course irrigation solution supplier.

These pumps have to cope with water that is often characterised by high abrasiveness, high alkalinity or high acidity. This is because water-scarcity issues, as well as a national requirement to provide for the country’s basic water needs, have resulted in many of South Africa’s golf courses switching from potable water to water sourced from effluent wastewater; rainfall runoff captured in ponds or reservoirs; streams and ponds; and groundwater.

The impact on wear rings

Prior to the introduction of Vesconite Hilube wear rings, the irrigation company used multiple-stage canister pumps with neck ring casings with phenolic wear rings.

Phenolic wear rings are typically made with a base material such as paper, fibreglass or cotton, which is permeated with a phenolic resin, or phenol formaldehyde resins.

Despite the fact that phenolic wear rings are seen as highly abrasion resistant, they were discovered to not be nearly wear-resistant enough to cope with the acidity levels and debris found in the storm water run-off and waste water that many South African golf courses are now using in line with global norms.

The phenolic wear rings, which were observably paper like, were found to delaminate, a process by which repeated stress causes the layers to separate. They tended to only last six to eight months.

The phenolic wear rings reduced pump performance. The pressure suddenly dropped, the client reported, noting the effect of the delamination and degradation of the wear rings, which are regarded as essential in this application since wear rings are typically used to create a virtual contact between a pump’s moving and stationary parts; to stabilise the pump rotor; and to reduce circulation between the pump stages.

The irrigation company approached Vesconite Bearings to produce differently-sized prototype wear rings for each of the pump sizes that it installs on South Africa’s golf courses. These were to be made of one of its polymers, Vesconite Hilube, a very strong, wear-resistant, low-friction, ultraviolet-stable engineered polymer that is also dimensionally stable in water.

After a year of testing at one golf course, the irrigation company still did not need to replace the wear rings and the wear rings showed no evidence of needing to be replaced. It began ordering sizeable quantities of wear rings from Vesconite Bearings so that it could install them as standard parts in the pumps that it was installing on South African golf courses.

The polymer wear rings were found to be suitable for the difficult water application, since they did not delaminate even when exposed to mild acids and alkalis or when in contact with abrasive materials. With the introduction of Vesconite Hilube wear rings, the dramatic pumping pressure drops and the frequent wear ring replacements also became a thing of the past.

Bowl bushings

The South African irrigation company also experienced difficulties with the carbon-graphite bowl bushings in the multiple-stage canister pumps before it introduced Vesconite Hilube bowl bushings.

Carbon-graphite is usually regarded as a hard-wearing material, since it includes the wear-resistance, strength and hardness of carbon and the self-lubricating characteristics and corrosion resistance of graphite. However, the abrasiveness of the grit and debris in the water that was being used for irrigation proved too much for the carbon-graphite bowl bushings too. Debris in the water sometimes caused the bushings to wear, with fast-moving fragments sometimes coming into contact with the impeller, damaging or removing vanes, and, in some cases, destroying the pumps.

Fine grit and fine particles also frequently embedded themselves into the carbon-graphite bushings and ate into stainless steel pump shafts.

As a consequence, shafts sometimes needed to be replaced, and, where shafts started vibrating due to shaft and bushing wear, the impellers came in contact with the metal chambers. The costs were considerable as canisters or even whole pumps sometimes had to be replaced.

Then the irrigation company introduced Vesconite Hilube bushings for seven canister pump models.

The results proved favourable, as a result of the Vesconite’s wear resistance.

Grit did not embed itself in the Vesconite Hilube bushings and lead to subsequent shaft damage and instability that damaged pump components.

The irrigation company was satisfied that after one year the bushings did not show significant wear and, importantly, there were no significant expenses related to bowl bushing failure.

It began ordering and stocking the Vesconite Hilube bowl bearings for use on the golf courses that it provides irrigation solutions to.

The benefits for golf courses with Vesconite wear rings and bowl bushings

Golf courses rely on the steady irrigation and are often viewed as undesirable places to play if they have visible stressed or burnt-out turf.

They are also averse to high maintenance costs including high electricity costs, which may be elevated if a pumping system is not operating optimally.

In addition, they are increasingly aware of the labour time, and the associated costs, involved in making repairs, managing and adjusting the irrigation system and hand watering dry areas where an irrigation system is found to be not optimal.

The case for ensuring that an irrigation system’s wear parts are well suited to the application is thus clear.

The benefits for the golf-course irrigation solution supplier

According to a presentation on the 2017 Golf Industry Outlook by Golf Course Industry, suppliers to the golf industry need to increasingly package what they sell as solutions rather than simply products. This would ensure that there is not a simple rush to the bottom in terms of price and that a knowledgeable supplier of appropriate solutions would be favoured over a supplier of a simple product that might not meet the needs of the client.

The presentation on the 2017 Golf Industry Outlook by Golf Course Industry also highlighted how tinkering and experimenting among golf-course superintendents is at an all-time high, and it seems that the trend towards independent thinkers, who are trying to optimise how resources are used to produce the best results on a golf course, may extend well beyond superintendents.

Vesconite Bearings is in favour of this approach, especially since it is self-evident that not all pre-packaged products work in all applications. The irrigation company that Vesconite Bearings supplied the wear parts to is well thought of in the industry, and a proactive technical team that are proactively searching for improved solutions to irrigation problems is one reason for this.

A last take-away

Turf-heads, as those who are knowledgeable about golf turf and the irrigation thereof like to be known, are convinced that water provision is the biggest long-term issue facing golf courses.

Several have even suggested that playing on natural grass may become a thing of the past, as concerns about water availability become paramount.

Irrigation using non-potable water sources is thus an inevitability if the continued use of natural turf is desired.  The use of storm water, water from dams and rivers, and effluent and wastewater all present technological challenges that the golf industry continues to address creatively, including in its assessment of the most suitable wear rings and bowl bushings for canister pumps.

More BushTalk Articles
Want to know more?

    Name *
    Email *
    Tel *
    Country *
    Street Address *
    Street Line 2
    Post Code *
    Province/State *